2004-2008 Chrysler Crossfire Front Driver Leather Steering Wheel OEM
Price list
Still could not find the Part? Contact us @ Find Exact Part in 24 Hours
Specification
| Brand | |
|---|---|
| MPN | A1934600003, A193 460 00 03 |
| Year | 2004, 2005, 2006, 2007, 2008 |
| Make | |
| Model | Crossfire |
| Trim | Limited Convertible 2-door, Limited Coupe 2-door, Base Convertible 2-door, Base Coupe 2-door, Srt-6 Convertible 2-door, Srt-6 Coupe 2-door |
| Engine | 3.2l 3200cc 195cu. In. V6 Gas Sohc Naturally Aspirated, 3.2l 3199cc V6 Gas Sohc Supercharged |
| Placement on Vehicle | Front-Left |
| Fitment Type | Direct Replacement |
| Material | Black Leather |
| Country / Region of Manufacture | Germany |
| Warranty | Lifetime |
| Part Number | A1934600003, 1934600003, A 193 460 00 03 0003, 19336512 6023328 023516 |
| Condition | Used |
Fit In Five Steps
How to replace a Chrysler Crossfire Steering Wheel?
1.Tools Required for Repair
- Metric Socket Set
- T30 Torx Socket
- 15/16″ or 24 mm socket
- ELECT-12, Air Bag Warning Light Reset
2.Locate & Secure Vehicle
Disconnect the battery negative lead. To prepare for removal of the steering wheel.
3.Remove the Steering Wheel for a Car without Airbags
- Remove the steering wheel horn pad by pulling firmly on the pad. It’ll be tough but, don’t worry about breaking it. If you have an aftermarket wheel (i.e. Momo) with a center horn button, gently pry around the outside of the button with a small flat tip screwdriver or probe to dislodge the button from the wheel.
- Disconnect the wire from the back of the horn button.
- Using a 15/16″ (or 24 mm) socket and ratchet, remove the steering wheel retaining nut and the washer behind the nut.
- Using a paint pen, fingernail polish, or other appropriate markers, mark the orientation of the steering wheel to the splines on the end of the steering column shaft.
- Pull the steering wheel straight off the end of the steering column.
4.Remove the Steering Wheel for a Car with Airbags
- The airbag can be removed after the battery has been disconnected for at least 30 minutes.
- On the back side of the steering wheel, there are two Torx head screws which are recessed into the back of the column. Using a T30 Torx socket and ratchet, remove the screws.
- Slide the airbag assembly off of the front of the steering column and disconnect the plug on the back of the airbag. Set the airbag aside where it can not get damaged (face up).
- Using a 15/16″ (or 24 mm) socket and ratchet, remove the steering wheel retaining nut and the washer behind the nut.
- Using a paint pen, fingernail polish, or other appropriate markers, mark the orientation of the steering wheel to the splines on the end of the steering column shaft.
- Pull the steering wheel straight off the end of the steering column.
5.Install the New Steering Wheel
- Slide the steering wheel on to the steering column paying attention to the alignment marks made during removal.
- Install the wheel retaining nut and torque to 45 Nm (33 ft-lbs).
- For non-airbag cars attach the horn button wire to the horn button pad and press the pad into place on the steering wheel.
- For airbag equipped cars, attach the wire to the back of the airbag, slide it into the steering wheel, and attach by installing the two Torx head screws (T30).
- Standing outside the car reach into the car and turn the ignition on. The reason for being outside the car is that this is one of the times I’ve seen airbags inadvertently deploy. Start the car and see if the airbag warning light is illuminated. If it is, reset the warning light using ELECT-12.
2004-2008 Chrysler Crossfire Front Driver Leather Steering Wheel OEM
$55.00
Got something to discuss?