SP9009M | 2007-2014 Toyota Tundra Sequoia Fuel Pump Sending Unit Module

0

Price list

Still could not find the Part? Contact us @ Find Exact Part in 24 Hours

Specification

Brand

, , ,

MPN

770200C072, E8806M, FG0932, P76710M, SP9009M

Year

2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014

Make

Model

Sequoia, Tundra

Trim

Base Crew Cab Pickup 4-Door, Base Extended Crew Cab Pickup 4-Door, Base Standard Cab Pickup 2-Door, Limited Crew Cab Pickup 4-Door, Limited Extended Crew Cab Pickup 4-Door, Limited Sport Utility 4-door, Platinum Crew Cab Pickup 4-Door, Platinum Extended Crew Cab Pickup 4-Door, SR5 Crew Cab Pickup 4-Door, SR5 Extended Crew Cab Pickup 4-Door, SR5 Premium Sport Utility 4-Door, SR5 Sport Utility 4-Door, SR5 Standard Cab Pickup 2-Door

Engine

4.0L 3956CC 241Cu. In. V6 GAS DOHC Naturally Aspirated, 4.6L 4608CC V8 GAS DOHC Naturally Aspirated, 4.7l 4663cc 285cu. In. V8 Gas Dohc Naturally Aspirated

Placement on Vehicle

Front

Fitment Type

Direct Replacement

Warranty

Lifetime

Part Number

23010343, 770200C072, A30153, A30432, A30433, E8806M, FG0932, P76710M, P76713M, SP9009M

Condition

New

Fit In Five Steps

BUY HERE

How to replace a Toyota Tundra Fuel Pump Sending Unit Module?

1.Materials Need for Repair

  • Ratchet wrench set with universal joint
  • Tubing or open-end wrenches
  • Hose clamp pliers or screwdriver
  • Bolt or wooden dowel
  • Shop rags
  • Gasket Sealer
  • The fire extinguisher rated for gasoline fires

2.Locate & Secure Vehicle

Disconnect the negative battery cable. Disconnect the fuel tank hose at the fuel pump and plug the hose with a bolt or wooden dowel to keep any fuel from flowing out. Also, disconnect the vapor-return hose if the vehicle is equipped with one. Be sure to wipe up any gas that spills. Carefully examine the old fuel hose; if it is frayed or cracked, replace it with new fuel line hose.

3.Remove Old Fuel Gas Pump & Sending Unit Module

Disconnect the outlet line to the carburetor. Use a wrench on the fuel pump fitting and another on the line nut. Remove the two attaching bolts and extract the old fuel pump. Clean off any old gasket material from the mounting surface of the engine using a shop rag. Once the old fuel pump has been removed, it’s time to prep and install the new unit in this order: Apply a coat of gasket sealer on both sides of the new gasket. Put the attaching bolts through the new pump and slip the gasket over the bolts.

4.Install New Fuel Gas Pump & Sending Unit Module

Install the new pump on the engine. Make sure that push rod is correctly installed in both the engine and the fuel pump. If the push rod slides out, you can pack it with some heavy grease to hold it in place while you install the pump. Attach the fuel outlet line that runs to the carburetor. If it’s difficult to connect, remove the other end of the line from the carburetor. Connect the line to the fuel pump, and then reattach the other end to the carburetor. Use a wrench to hold the fuel pump fitting and tighten the line nut with another wrench.

5.Replace Removal Parts & Check for Leakage

Attach the fuel inlet hose from the gas tank and the vapor-return hose. Tighten all clamps. Reconnect the battery ground cable, start the vehicle, and check for leaks.
BUY HERE

Got something to discuss?


 
SP9009M | 2007-2014 Toyota Tundra Sequoia Fuel Pump Sending Unit Module
SP9009M | 2007-2014 Toyota Tundra Sequoia Fuel Pump Sending Unit Module