25500-23010 25500-23001 | 1996-2016 Hyundai Kia 2.0L 2.4L 1.8L DOHC I4 Thermostat Assembly
Price list
Still could not find the Part? Contact us @ Find Exact Part in 24 Hours
Specification
| Brand | |
|---|---|
| MPN | 25500-23010 |
| Year | 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 |
| Make | |
| Model | Accent, Elantra, Forte, Optima, Rio, Rondo, Santa Fe, Sonata, Sorento, Soul, Spectra, Spectra5, Sportage, Tiburon, Tucson |
| Trim | Coupe 2-Door, Hatchback 2-Door, Hatchback 3-Door, Hatchback 4-Door, Hatchback 5-Door, Sedan 4-Door, Sport Utility 4-Door, Wagon 5-Door |
| Engine | 1.5L 1495CC l4 GAS DOHC Naturally Aspirated, 1.6L 1600CC l4 GAS DOHC Naturally Aspirated, 1.8L 1795CC l4 GAS DOHC Naturally Aspirated, 2.0L 1997CC l4 GAS DOHC Naturally Aspirated |
| Placement on Vehicle | Front-Lower |
| Fitment Type | Direct Replacement |
| Material | Bimetallic |
| Country/Region of Manufacture | Korea, Republic |
| Warranty | 2 Year |
| Part Number | 25500 23010, 25500-23010, 2550023010, 25620-23501, 2562023501 |
| Condition | New |
Fit In Five Steps
How to replace a Hyundai Kia 2.0L 2.4L 1.8L DOHC I4 Thermostat Assembly?
1.Locate Your Thermostat
Most thermostats are located where the top radiator hose joins the engine, so these steps deal with this type. If your thermostat is in the bottom radiator hose, the principle is the same. Place a bucket under where you’re going to be working. Some fluid will escape, so have a clean two-gallon container handy to catch it, and return the fluid to the radiator when you finish the job.
2.Remove the Clamp & Pull Off The Hose
Follow your radiator hose to where your thermostat is located. This is when some fluid will escape and drain into your bucket.
3.Remove Old Thermostat
Remove the bolts that hold the thermostat housing in place and lift out the old thermostat. Compare the new thermostat and its gasket with the old ones. If the new thermostat and the gasket that’s included with it aren’t exactly like the old ones, go back to the store for the right ones.
4.Install New Thermostat
There’s a gasket around the hole where the thermostat was located — take that off, too. Scrape off any pieces of a gasket that may be stuck, but be sure not to let these pieces fall into the hole! Make sure to place the spring-side down; then replace the bolts.
5.Replace Removal Parts & Check Leakage
If your hose clamp uses screws, screw it down tightly but not tight enough to cut into the hose. Replace whatever fluid ran out of the hose by pouring it from the container into the radiator fill hole or coolant reservoir. Be sure not to pour it on the ground where children and animals can be endangered by it. If you accidentally spill fluid, wipe it up thoroughly before hosing down the area, and then place the rags in a sealed plastic bag before disposing of them.
$8.00
Got something to discuss?