741-5403 & 741-5404 | 2009-2011 Kenworth W900 T600 T800 Power Window Regulator Pair
Price list
Still could not find the Part? Contact us @ Find Exact Part in 24 Hours
Specification
| Brand | |
|---|---|
| MPN | 741-5403; 741-5404 |
| Year | 2009, 2010, 2011 |
| Make | |
| Model | T660, T800, W900 |
| Trim | Base Straight Truck – Long Conventional, Base Tractor Truck – Long Conventional |
| Engine | 10.8L 10834CC 661Cu. In. l6 DIESEL Turbocharged, 11.9L 726Cu. In. -6 DIESEL, 12.5L 763Cu. In. -6 DIESEL, 15.0L 15000CC 915Cu. In. l6 DIESEL Turbocharged |
| Placement on Vehicle | Front-Right, Left |
| Fitment Type | Direct Replacement |
| Material | Metal |
| Warranty | Lifetime |
| Part Number | 741-5403; 741-5404, AM-885422285, DMDRK00005, R21-1005; R21-1005R, R211005; R211005R |
| Condition | New |
Fit In Five Steps
How to replace a Kenworth W900 T600 T800 Power Window Regulator?
1.Removing the Door Panel
- Pry off the trim piece inside the door handle with a flat blade screwdriver
- Pry up the window switch panel with a flat blade screwdriver
- Disconnect the window switch wiring harnesses
- Pull off the side panel next to the window
- Remove the 6mm bolt next to the window
- Remove the two 8mm bolts inside the door handle
- Remove the 10mm bolt inside the door pull
- Remove the two 6mm bolts at the bottom of the door panel
- Pry out the door panel
- Lift the door panel up and off
- Disconnect the latch cables from the door handle
- Remove the 5.5mm or 7/32 bolts from around the speaker
- Pull off the speaker
- Disconnect the speaker wiring lead
- Carefully peel off the water shield
2.Removing the Window Regulator
- Loosen the two 10mm bolts that hold the window to the regulator
- Pry your fingers between the cushions holding the window
- Raise the window by hand
- Hold the window in place with painter’s tape
- Disconnect the window motor lead
- Remove the four 10mm bolts from the regulator
- Remove the 10mm bolt from the window motor
- Unclip the wire on the door
- Pull the window regulator out through the door
3.Installing the New Window Regulator
- Push the regulator into the door
- Hang the regulator by its bolts
- Tighten the four 10mm bolts into the regulator
- Tighten the 10mm bolt into the regulator motor
- Push the clip into the door
- Connect the window motor to the lead
4.Testing the Regulator
- Connect the window switch to the switch panel
- Turn the vehicle on
- Run the motor up for 4 seconds
- Disconnect the switch panel
5.Reinstalling the Door Panel
- Put the water shield into place
- Insert the 5.5mm or 7/32 bolts around the speaker
- Connect the speaker wiring lead
- Put the speaker in place
- Connect the latch cables to the door handle
- Lift the door panel into place
- Push in the door panel clips
- Insert the two 6mm bolts at the bottom of the door panel
- Insert the two 8mm bolts inside the door handle
- Insert the 10mm bolt inside the door pull
- Insert the 6mm bolt next to the window
- Connect the window switch wiring harness
- Push in the switch panel
- Push on the trim piece inside the door handle
- Push on the trim panel next to the window
741-5403 & 741-5404 | 2009-2011 Kenworth W900 T600 T800 Power Window Regulator Pair
$349.90
Got something to discuss?