2009-2013 Ram 1500 2500 3500 OEM 5″ Oval Black Aluminum Tube Side Step Pads Running Boards
Price list
Still could not find the Part? Contact us @ Find Exact Part in 24 Hours
Specification
| Brand | |
|---|---|
| MPN | 82212087AD, 82212087AE, 82212087AF |
| Year | 2009, 2010, 2011, 2012, 2013 |
| Make | |
| Model | 1500, 2500, 3500 |
| Trim | Laramie Cab & Chassis 4-Door, Laramie Crew Cab Pickup 4-Door, Laramie Extended Crew Cab Pickup 4-Door, Laramie Longhorn Crew Cab Pickup 4-Door, Laramie Longhorn Extended Crew Cab Pickup 4-Door, Outdoorsman Extended Crew Cab Pickup 4-Door, SLT Cab & Chassis 2-Door, SLT Cab & Chassis 4-Door, SLT Crew Cab Pickup 4-Door, SLT Extended Crew Cab Pickup 4-Door, SLT Standard Cab Pickup 2-Door, ST Cab & Chassis 2-Door, ST Cab & Chassis 4-Door, ST Crew Cab Pickup 4-Door, ST Standard Cab Pickup 2-Door, SXT Cab & Chassis 2-Door, SXT Cab & Chassis 4-Door, SXT Crew Cab Pickup 4-Door, SXT Standard Cab Pickup 2-Door |
| Engine | 5.7L 345Cu. In. V8 BI-FUEL OHV Naturally Aspirated, 5.7L 345Cu. In. V8 GAS OHV Naturally Aspirated, 6.7L 408Cu. In. l6 DIESEL OHV Turbocharged |
| Placement On Vehicle | Front |
| Fitment Type | Direct Replacement |
| Surface Finish | Black Aluminum |
| Warranty | 1 Year |
| Part Number | 82212087AE, 82212087AD, 82212087AC, 82212087AB, 82212087AF |
| Condition | New |
Fit In Five Steps
How to replace a Ram 1500 Running Boards?
1.Secure Vehicle
Line up the running boards/nerf bars on both sides, making sure they are the right ones for the truck. Make sure that they fit snugly under the frame below the particular area they install on. Check to see whether there are predrilled holes or if the holes will have to be drilled by hand. Unscrew the two body mount bolts from each side of the truck. These bolts are located under the front part of the doors and under the rear part of the cab, before the box of your truck.
2.Unbolt Screws
To drill the holes by hand, have a friend help in holding the running board/nerf bar against the body of the truck where it goes. Mark where the holes need to be drilled with a marker. Set the running board/nerf bar aside. The bolt will have a large rubber washer on it. Place each bolt through the bracket that came with the nerf bars.
3.Remove Running Boards/Nerf Bars
Double check where the holes will be drilled to make sure the areas for the holes are sturdy. The running board/nerf bar may have to be adjusted at this time to accommodate this. If so, remark the drill points. Place the rubber washer between the bracket and the truck body.
4.Install New Running Boards/Nerf Bars
Drill holes in the body of the truck using a power drill and metal drill bits. This might require smaller drill bits at first, switching to bigger drill bits until the desired size of the hole is reached. Screw the bolts back into place and make sure the brackets are facing outward. Replace a New side step running boards on your vehicle.
5.Rearrange Removal Parts
With the help of a friend, hold the running board/nerf bar in place and tighten the screws or bolts, depending on what is used. Vehicle owners should test the running boards/nerf bars for sturdiness by stepping and putting their full weight on them. Hold the nerf bar to the brackets. Have a friend screw at each end of the nerf bar to the brackets.
BUY HERE
$299.00
Got something to discuss?