24503623 | 1988-1992 Buick Chevrolet Oldsmobile Pontiac Magnavox Style Ignition Control Module Coil Kit Set

0

Specification

Brand

, , ,

MPN

1AERK00307, AM-3155592362, SMP DR-36T, LX-349T, OE # 24503623

Year

1988, 1989, 1990, 1991, 1992

Make

, , ,

Model

88, 98, Bonneville, Electra, Lesabre, Park Avenue, Reatta, Riviera, Toronado

Trim

Custom, Limited, Ultra, Royale Ls, Royale, Regency, Touring, Regency Elite, Se, Sse, Ssei, Royale Brougham, Le, Park Avenue, T-type – Sedan 4-door \ Limiuted, Base, Royale Brougham, Royale, Custom, Luxury, Trofeo, T-type – Coupe 2-door

Engine

3.8l 3800cc 231cu. In. V6 Gas Ohv Naturally Aspirated, 5.0l 307cu. In. V8 Gas Ohv Naturally Aspirated, 3.8l 3800cc 231cu. In. V6 Gas Ohv Supercharged

Placement on Vehicle

Front

Fitment Type

Direct Replacement

Country/Region of Manufacture

United States

Warranty

Lifetime

Part Number

1AERK00307, AM-3155592362, SMP DR-36T, LX-349T, Hollander 610-02173, 610-02756, OE # 24503623

Condition

New

Fit In Five Steps

How to replace a Buick Chevrolet Ignition Control Module Coil?

1.Secure Vehicle

Park your vehicle in a safe place and locate the ignition module. Look at the dashboard. If yours is mounted here, unplug the module wiring harness. Remove the mounting bolts using a Phillips screwdriver or ratchet and socket. Replace the old unit with the new module and install the mounting bolts. Plug the wiring harness.

2.Replace Distributor Cap

Open the hood and remove the distributor cap using a Phillips screwdriver or ratchet and socket, but do not disconnect the spark plug wires from the distributor cap. Some ignition modules are mounted inside the distributor. Unplug the electrical connector from the module and remove the mounting bolts using a Phillips screwdriver or ratchet and socket. Replace the old module with the new unit and install the mounting bolts. Replace the distributor cap.

3.Locate & Access Distributor

Look on one side of the distributor. Some modules are attached to the outside case of the distributor. Mark the exact mounting location of the distributor base on the engine so you can reinstall the distributor at the same exact location to avoid disturbing the engine timing.

4.Remove Old Ignition Control Module

Remove the distributor cap using a Phillips screwdriver or ratchet and socket, but do not remove the spark plug wires. Remove the distributor mounting bolts and lift the distributor off the engine compartment. Remove the ignition module mounting bolts and install the new module in place. Install the distributor on the engine following the match-mark and install the distributor cap.

5.Replace New Ignition Control Module

Look for the ignition coil and module assembly. Follow the spark plug wires starting with the spark plugs. The wires connect to the coil and module assembly, which may be mounted on the back of the engine. You might have to raise the front of your car using a floor jack and safely support it on two jack stands. Reach under the engine and unplug the coil assembly electrical connectors. Remove the assembly mounting bolts using a ratchet and socket. Remove the assembly from the engine and remove the coils using a ratchet and socket. Remove the old ignition module from the base plate and install the new unit. Install the coils and module assembly on the engine. Plug the electrical connectors and lower the vehicle.

Got something to discuss?


 
24503623 | 1988-1992 Buick Chevrolet Oldsmobile Pontiac Magnavox Style Ignition Control Module Coil Kit Set
24503623 | 1988-1992 Buick Chevrolet Oldsmobile Pontiac Magnavox Style Ignition Control Module Coil Kit Set