Specification

Brand

, , , ,

MPN

134.45510, EW15509, WC37751, WCA37751

Year

1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993

Make

Model

B2000, B2200, B2600

Trim

Base Extended Cab Pickup 2-Door, Base Standard Cab Pickup 2-Door, LE-5 Extended Cab Pickup 2-Door, LE-5 Standard Cab Pickup 2-Door, LX Extended Cab Pickup 2-Door, LX Standard Cab Pickup 2-Door, SE-5 Extended Cab Pickup 2-Door, SE-5 Standard Cab Pickup 2-Door, Sundowner Base Standard Cab Pickup 2-Door, Sundowner SE-5 Standard Cab Pickup 2-Door, Sundowner Sport Standard Cab Pickup 2-Door

Engine

2.0L 1998CC 122Cu. In. l4 GAS SOHC Naturally Aspirated, 2.2L 2184CC l4 GAS SOHC Naturally Aspirated, 2.6L 2555CC l4 GAS SOHC Naturally Aspirated, 2.6L 2606CC l4 GAS SOHC Naturally Aspirated

Placement on Vehicle

Rear-Right

Fitment Type

Direct Replacement

Material

Steel

Warranty

1 Year

Part Number

072-8349, 1.80E286, 1.8E286, 134.45510, 33950, 538 32014 714, EW155091, UB39 26 610, W37751, WC37751, WCA37751

Condition

New

Fit In Five Steps

How to replace a Mazda B2000 B2200 B2600 Brake Master Wheel Cylinder?

1.Clean Up Before You Start

Before you start wrenching on your braking system, you need to thoroughly clean all of the parts involved. The inside of a brake system is very sensitive to dirt and debris. Even the smallest piece can cause wear and malfunction. Spray the master cylinder, brake lines, and other components liberally with brake cleaner. Let it soak and do it again. If it’s extra gooey in there, you might need to steal your kid’s toothbrush to take care of it. No matter how you do it, be sure the area is clean before you even remove the brake fluid cap. Once you’ve got everything spic-n-span, remove the fluid reservoir cap and suck the old brake fluid out with your turkey baster. Don’t worry about getting every drop; you’re just making the next steps a little cleaner.

2.Loosen the Brake Lines

If your car has a “low brake fluid” sensor in the fluid reservoir cap or any other wiring (such as ABS) on the master cylinder, unplug them. Now take your line wrench and loosen all four brake lines at the master cylinder, but don’t unscrew them all the way yet! You want to leave them in there just a little bit. You’ll see why in the next steps.

3.Unbolt the Master Cylinder

With the brake lines loosened but not removed, you can remove the bolts that hold the master cylinder in place. It’s usually bolted to a brake booster of some shape or size, but you can look at your new master cylinder to see exactly what you should be removing. With the master cylinder bolts removed, you can lift the master cylinder up slightly (if needed) and remove the four brake lines. We left them screwed in slightly because often you aren’t able to pull them all the way out because of shock tower clearance. It’s not fun having to rethread all the brake lines so that you can get them out enough to remove.

4.Retrieve the Rear Master Cylinder Seal

With the master cylinder removed you’ll be able to see the rod that pushes the piston in the master cylinder. If it didn’t come off with the master cylinder, there will also be a seal around the pushrod. Remove this seal. If your master cylinder came with a new seal, you’d be replacing it. If not, clean it up for reuse. It still needs to come out temporarily.

5.Reinstall and Wrapping Up

Now that you’ve removed the old master cylinder, you’re ready to install the new part. But before you do, it’s a good idea to bench bleed the master cylinder. It’s much easier to get the air out now than later. It goes in just like it came out, so in the words of service manuals around the world, “installation is the reverse of removal.”Once the new part is installed, you’ll need to add new brake fluid (never try to reuse the old stuff) and bleed the brakes. Now you’re ready to go!

Got something to discuss?


 
1986-1993 Mazda B2000 B2200 B2600 Rear Right Drum Brake Wheel Cylinder
1986-1993 Mazda B2000 B2200 B2600 Rear Right Drum Brake Wheel Cylinder