Specification

Brand

, ,

MPN

1AWRG00204, AM-41314980, G2014000105-ST-ZD16428-FR, ST-ZD16428-FR, ZD164135-FR

Year

2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010

Make

, ,

Model

Aviator, Explorer, Mountaineer

Trim

Cab Pickup 4-Door, Sport Utility 4-Door

Engine

4.0L 245Cu. In. V6 GAS SOHC Naturally Aspirated, 4.6L 281Cu. In. V8 GAS SOHC Naturally Aspirated

Placement on Vehicle

Front-Right

Fitment Type

Direct Replacement

Warranty

Lifetime

Part Number

125-2039, 125-2815, 1AWRG00204, 4L2Z7823200BA, 6L2Z 7823200 AA, 741-814, AM-41314980, G2014000105-ST-ZD16428-FR, ST-ZD16428-FR, ZD164135-FR

Condition

New

Fit In Five Steps

BUY HERE

How to replace a Ford Power Window Regulator & Motor?

1.Removing the Door Panel

  • Pry off the trim piece inside the door handle with a flat blade screwdriver
  • Pry up the window switch panel with a flat blade screwdriver
  • Disconnect the window switch wiring harnesses
  • Pull off the side panel next to the window
  • Remove the 6mm bolt next to the window
  • Remove the two 8mm bolts inside the door handle
  • Remove the 10mm bolt inside the door pull
  • Remove the two 6mm bolts at the bottom of the door panel
  • Pry out the door panel
  • Lift the door panel up and off
  • Disconnect the latch cables from the door handle
  • Remove the 5.5mm or 7/32 bolts from around the speaker
  • Pull off the speaker
  • Disconnect the speaker wiring lead
  • Carefully peel off the water shield

2.Removing the Window Regulator

  • Loosen the two 10mm bolts that hold the window to the regulator
  • Pry your fingers between the cushions holding the window
  • Raise the window by hand
  • Hold the window in place with painter’s tape
  • Disconnect the window motor lead
  • Remove the four 10mm bolts from the regulator
  • Remove the 10mm bolt from the window motor
  • Unclip the wire on the door
  • Pull the window regulator out through the door

 3.Installing the New Window Regulator

  • Push the regulator into the door
  • Hang the regulator by its bolts
  • Tighten the four 10mm bolts into the regulator
  • Tighten the 10mm bolt into the regulator motor
  • Push the clip into the door
  • Connect the window motor to the lead

4.Testing the Regulator

  • Connect the window switch to the switch panel
  • Turn the vehicle on
  • Run the motor up for 4 seconds
  • Disconnect the switch panel

5.Reinstalling the Door Panel

  • Put the water shield into place
  • Insert the 5.5mm or 7/32 bolts around the speaker
  • Connect the speaker wiring lead
  • Put the speaker in place
  • Connect the latch cables to the door handle
  • Lift the door panel into place
  • Push in the door panel clips
  • Insert the two 6mm bolts at the bottom of the door panel
  • Insert the two 8mm bolts inside the door handle
  • Insert the 10mm bolt inside the door pull
  • Insert the 6mm bolt next to the window
  • Connect the window switch wiring harness
  • Push in the switch panel
  • Push on the trim piece inside the door handle
  • Push on the trim panel next to the window

Got something to discuss?


 
2002-2010 Ford Lincoln Mercury Front Power Window Regulator & Motor Passenger Right RH
2002-2010 Ford Lincoln Mercury Front Power Window Regulator & Motor Passenger Right RH