992757-5211-1154081 | 1999-2016 Jeep Wrangler Grand Cherokee (4) 2″ 5×5 Wheel Spacers Adapters
Price list
Still could not find the Part? Contact us @ Find Exact Part in 24 Hours
Specification
| Brand | |
|---|---|
| Year | 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 |
| Make | |
| Model | Commander, Grand Cherokee, Wrangler |
| Trim | Sport Utility 4-Door |
| Engine | 3.6L 3604CC 220Cu. In. V6 GAS DOHC Naturally Aspirated, 3.7L 226Cu. In. V6 GAS SOHC Naturally Aspirated, 3.8L 3778CC 231Cu. In. V6 GAS OHV Naturally Aspirated, 4.0L 242Cu. In. l6 GAS OHV Naturally Aspirated, 4.7l 287cu. In. V8 Gas Sohc Naturally Aspirated, 5.7L 345Cu. In. V8 GAS OHV Naturally Aspirated, 6.1L 6059CC 370Cu. In. V8 GAS OHV Naturally Aspirated |
| Placement on Vehicle | Front |
| Fitment Type | Direct Replacement |
| Vehicle Bolt Pattern | 5×5 / 5×127" |
| Thickness | 2" / 50mm |
| Wheel Bolt Pattern | 5×5 / 5×127" |
| Thread Size | 1/2"x20 |
| Surface Finish | Silver |
| Quantity | 4 Pieces |
| Warranty | 1 Year |
| Part Number | 992757-5211-1154081, ASF992757R01, ECP99275701, US992757DIY |
| Condition | New |
Fit In Five Steps
How to replace a Jeep Wrangler Grand Cherokee Wheel Spacer Adapters?
1.Secure Vehicle
Park your car or truck on a level surface. Loosen the lug nuts that fasten the wheel to the hub. Slide a floor jack under the car at the appropriate point and jack up the car. Lower the car onto a jack stand. Repeat this process until all four corners are supported on a jack stand.
2.Prepare for Removal Process
Finish removing the lug nuts. Slide the wheels off the hub and set them out of the way. Spray degreaser on the lug studs and wipe them down with a rag. If they are very dirty, use a wire brush to clean up the threads. Wipe down the hub surface where the wheel installs, as well.
3.Remove Old Wheel Adapters(Spacers)
Slide the wheel spacer onto the studs, if it is not the bolt-on type. Line the holes in the spacer up with the wheel studs and then slide the spacer over the studs until it seats firmly against the hub. Some vehicle (BMWs for instance) use lug bolts that thread into the hub. In this case, line up the spacer with the holes in the hub.
4.Place New Wheel Adapters(Spacers)
Place the wheel spacer onto the studs, if it is a bolt-on wheel spacer. Install the lug nuts onto the studs so that the spacer is bolted to the hub. The bolts will come with the spacer but are also available at auto parts stores if they are not with the spacer. Tighten the nuts that hold the spacer in place to the specifications outlined in the directions. This will likely be around 90 foot-pounds. Slide the wheel onto the lug studs so that it seats firmly against the spacer. Install the lug nuts (or lug bolts) with the lug wrench and tighten them. Repeat for the other corners of the vehicle.
5.Reinstall Removal Part & Check for Drive
Slide the floor jack under the car and lift the vehicle so that the jack stands can be removed. Lower the vehicle to the ground, one corner at a time. Tighten the lug nuts with a torque wrench in a crisscross, star pattern. Tighten them to the manufacturer’s recommended setting, which should be anywhere from 70 to 90 foot-pounds, depending on the vehicle. Check the tightness of the lug nuts after the vehicle has been driven 100 miles.
$66.49
Got something to discuss?